Frequently Asked Questions

Our customers most Frequently Asked Questions

A-arm / Ball Joint install

  1. Bolts and nut tork spec
  2. Stud spins in steering knuckle
  3. Grease

 

Get live shipping quotes on JBA web site from Marlin Gehman on Vimeo.

Overseas shipments

  1. Yes, we ship our parts all over the world
  2. Get live shipping quotes on JBA web sites

 

If you have product related questions post them below and we will post the answer to help all our customers.

28 thoughts on “Frequently Asked Questions”

  • Daryl

    Do you have any plans to build heavy duty high caster upper a-arms for the 1996-2004 Toyota Tacoma?
    If yes, when would they be available and what would the price be?
    Thank you, Daryl

    Reply
  • Jason Smith

    When were these available for 96-04 Tacomas? I was looking for new control arms back in April and didn't want to get uniballs. I saw the ones for 2nd gen Tacomas. I ended up buying SPC units. How did I miss these?

    Reply
  • Jay Pena

    Marlin,

    I installed the JBA ARMs for a lifted WK, and am loving them. Thank you. Quick question, do I need to grease them or do them come pre-greased?

    Reply
  • Jay Pena

    Marlin,

    I watched the video and found the answer regarding grease, can I order two more washers for the ball joint, I used them against the nut and they are marred with the edges of the bolt.

    Reply
  • Travis Willis

    This may be a dumb question but you guys have a option when selecting your UCAs- Option 1: pre-assembled with red powder coated.. Option 2: Un-assembled and un-coated.... my question is with the 2nd option, with it being "un-coated" do they need to be painted to be protected from rust? or do you guys base coat them with something. I'm just curious because i'm not a fan of red. and don't mind them being Un-assembled. but i just wanna know if i need to paint them to protect them from the elements. Thanks for you time!

    Reply
  • Chris W

    I have a set of standard high caster upper control arms for my 10 Tacoma. My question is that I bought a set of Energy suspension poly control arm bushings for my lower control arm and they came with the bushings for uppers as well. Will the Energy suspension upper control arm bushings fit in the JBA uppers if the ES bushings will fit the stock uppers? Thank you very much, and excellent product by the way.
    Sincerely,
    Christopher M Wehling
    484-624-7747

    Reply
    • Marlin Gehman

      Chris, our bong is the same size as factory so yes it should fit. I am just concerned the poly will squeak over time. We have synthetic elastomer a-arm bushings. Synthetic Elastomer is a long-chained polymer with many urethane constituents. Over the years the formulation has evolved to yield stronger, yet softer compounds ideal for on and off-road applications. As the compound advanced to yield higher tensile strength, elasticity, and dynamic load capacity, JBA uses the bushing to help aid and tune suspension geometry and get rid of squeaky poly urethane bushings. http://jbaoffroad.com/2005-2015-tacoma-upper-control-arm-bushing-kit-jba-69000.html

      Reply
      • Joe H

        I just purchased the un-assembled and un-coated control arms that come with the Synthetic Elastomer bushings. The control arms have grease fittings for the bushings. I lubricated the bushings and steel sleeves with the grease supplied in the kit when installing them. What type of grease should I use and how often should I grease these bushings in the future?

        Reply
  • Mike Edgar

    Will the "JBA Upper A-arms for lifted WK2" fit on a 2016 Jeep GC?

    Reply
  • Benny Migliorino
    Benny Migliorino October 9, 2017 at 8:01 am

    Hello,

    I have a 03 KJ. What is involved if I want to change the front end to a sold setup?

    Benny

    Reply
  • Aaron Reilly

    Hi Marlin,

    I just received the UCAs for my 1st gen Tacoma, and having a hard time understanding the instructions. It seems that I need to disassemble the ball joint in order to get it pressed into the spindle - is this correct? If so, what is the best way to remove the metal cap without the small tool that you use in the video? Thanks for your help.

    Reply
    • Marlin Gehman

      Aaron,
      yes, you need to remove the factory ball joint from the steering knuckle. You can beat it out of the steering knuckle with a big hammer if you do not have the tool to remove it.

      Reply
  • J. Dale Garrett
    J. Dale Garrett November 1, 2017 at 9:04 am

    Just purchased UCA for 1st gen Tacoma. All started with LBJ failure. Toyota design for LBJs is poor. Only way to get a safer design is buy aftermarket and all I can find is long travel. I don’t want long travel but do want a safer design. Will you all consider making a safer design factory length LCA?

    Reply
  • Allen

    When purchasing the OME lift for the KJ if I also ordered the labor to assemble the front struts does that mean I won't need a spring compressor to do the front?

    Reply
  • Mat Burkett

    I plan to purchase your struts and 4" coil springs for my 02 KJ. Will I need the "cut" cv axles? And do you mind explaining why? I'm not very familiar with IFS.
    Thank you
    Mat

    Reply
    • Marlin Gehman

      Jeep Liberty CV axle assembly with the 1/2" machined off the face of the inner joint. With this assembly you can lift you Jeep Liberty 2-1/2" to 4.0" and the CV joints will not fail with normal use. On factory CVs with a 4.0" lift the CV bind up and split the inner CV housing. Also the cheep China CVs have a 3 bearing trunnion that does not hold up in a lifted vehicle.

      Reply
Leave a Reply