Trail-dirty red JBA Offroad upper control arm with a greaseable Max 90 ball joint on a lifted truck

Greasing your upper control arms takes a few minutes, but a few small mistakes can leave a ball joint dry or tear a boot. Here are the 5 tips we share most, from picking the right grease to greasing your control arms properly. 

The short version: use a lithium moly EP grease (our pick is Mobilgrease XHP 222 Special), give each ball joint 3 to 4 pumps, fill the bushings until grease pushes out of the EZ Lube ports, and do it every 3,000 to 5,000 miles. Skip Red 'n Tacky.

Every moving part on a JBA upper control arm has its own grease fitting. That's on purpose. Tire size, terrain and driving style all affect how long your ball joints and bushings last, but greasing is the one part you control. A few minutes with a grease gun every oil change or two is the cheapest suspension maintenance you'll ever do!

JBA Offroad builds USA-made upper control arms for lifted and leveled Toyota, Lexus, Ford, Jeep, Ram and more in our shop in Souderton, Pennsylvania. Every JBA arm has a greaseable, replaceable Max 90 ball joint and greaseable EZ Lube bushings, so everything in this guide applies to every arm we make.

Why greasing matters more on a lifted or leveled truck

A lift or leveling kit makes your upper control arms work harder. Factory arms end up at a steeper angle than they were built for, caster drops, and the upper ball joint runs closer to the edge of its travel. Add bigger tires and trail miles, and the ball joints and bushings carry more load than stock.

Fresh grease is what keeps that extra load from turning into extra wear. The catch is that many factory arms use sealed ball joints. Once the factory grease breaks down, there's no way to add more, and wear speeds up from there.

That's why every JBA upper control arm has a grease fitting on the ball joint and on each bushing. Not sure your lift needs new arms? Start with Do lifted trucks need upper control arms? and lifted suspension wear: why parts fail faster without proper geometry.

Looking for your vehicle? See our guides for the Tacoma, 4Runner, Tundra, Lexus GX, F-150 with a leveling kit, Bronco and Ram 1500.

Greasing JBA upper control arms at a glance

WhatJBA recommendation
Grease to useMobilgrease XHP 222 Special, a lithium complex grease with 0.75% moly
AlternativesOther lithium moly EP greases with a similar makeup
Grease to avoidLucas Red 'n Tacky, other red greases and some synthetics
Ball joints3 to 4 pumps, until the dust boot starts to swell
BushingsPump until grease pushes out of the EZ Lube ports
How oftenEvery 3,000 to 5,000 miles
Extra greasingAfter any day in mud, creeks or water crossings
What you needA grease gun and one cartridge. Grease is $15; the grease gun and grease bundle is $45.54

Prices as of November 2026.

5 tips for greasing your JBA upper control arms

1. Use the right grease (and skip the one that ruins bushings)

Cartridge of Mobilgrease XHP 222 Special lithium moly grease, the grease JBA recommends for upper control armsCartridge of Mobilgrease XHP 222 Special lithium moly grease, the grease JBA recommends for upper control arms
Mobilgrease XHP 222 Special, the lithium moly grease we recommend for every JBA arm.

Use a lithium moly EP grease. Our pick is Mobilgrease XHP 222 Special, and it's the grease we stock and recommend for every JBA arm.

  • Moly for heavy loads. It's fortified with 0.75% molybdenum disulfide, which protects against wear when a joint pivots under load (that's exactly what a ball joint does all day!)
  • Holds up to water. It resists washout, so it stays put through creek crossings and wet winter roads.
  • Handles heat. It's rated up to 140°C (284°F).

Make sure you get the Special version - its the only one that contains moly. If you can't find it locally, other lithium moly EP greases with a similar makeup will do the job.

Now the grease that ruins bushings: Lucas Red 'n Tacky. It makes the bushings squeak within a short time and can eventually damage them. We've seen the same problems with other red greases and some synthetics. PLEASE DON'T USE IT!

2. Prime your grease gun before you start

Grease gun coupler pressed onto the grease fitting of a JBA Max 90 ball jointGrease gun coupler pressed onto the grease fitting of a JBA Max 90 ball joint
Push the coupler square and firm onto the fitting so grease goes into the joint, not around it.

A grease gun that isn't primed pumps air. The handle still moves, so it feels like you're greasing, but little or no grease makes it into the ball joint or bushings. That's how a "freshly greased" joint ends up running dry.

To prime it:

  • Load the cartridge and leave the head about one thread loose, or crack the air bleeder valve if your gun has one.
  • Pump the handle until grease flows steadily out of the coupler, then tighten everything down.
  • Give it a pump onto a rag. You want a steady bead of grease, not sputters.
  • Push the coupler square and firm onto the fitting. If grease squeezes out around the coupler, it isn't going into the joint.

If the gun stops pushing grease halfway through, it's almost always an air pocket. Bleed it and prime it again. Our grease gun and grease bundle comes with a 4-jaw coupler that grips the fitting and a 12-inch flexible hose for reaching tight spots.

This matters more than it sounds. JBA Max 90 ball joints use a wear-compensating upper race that slides up and down and is kept under load by an internal spring. That race needs grease to move freely. A cheap, worn or unprimed gun can struggle to push grease through the joint's tight tolerances and small grease channels, and the race can stick in the up position. That makes the whole ball joint feel loose and worn out. A thorough greasing with a good gun usually pushes the race back where it belongs. It's like getting a new ball joint for about 50 cents' worth of grease and a minute of your time.

3. Don't stop too early

Grease pushing out of the EZ Lube ports on a JBA upper control arm bushing, showing the bushing is fullGrease pushing out of the EZ Lube ports on a JBA upper control arm bushing, showing the bushing is full
Grease pushing out of the EZ Lube ports means the bushing is full.

One quick pump isn't enough. Too little grease leaves the old, dirty grease and any water sitting in the joint, and that's what wears it out.

  • Ball joint: 3 to 4 pumps, until the dust boot just starts to swell.
  • Bushings: JBA EZ Lube bushings have 8 grease ports and pressure-relief valves. Keep pumping until grease consistently pushes out of the EZ Lube ports. That fresh grease flushes the contaminated grease out ahead of it.

4. Don't overfill the ball joint

Overfilled JBA Max 90 ball joint boot ballooned out under a red JBA upper control armOverfilled JBA Max 90 ball joint boot ballooned out under a red JBA upper control arm
Overfilled: the boot balloons and stretches. Stop pumping when it just starts to swell.

More isn't better. Once the boot starts to swell, the ball joint is full.

Keep pumping past that and the boot balloons up. Our boots fit snugly to keep dirt and moisture out, so when a joint is overfilled, the extra grease vents wherever it can to keep the boot from blowing up like a balloon and bursting. Remember, the dust boot plays no role in lubricating the ball joint. The grease only needs to fill the inside of the steel housing.

Overfilled JBA Max 90 ball joint with excess grease forced out around the top capOverfilled JBA Max 90 ball joint with excess grease forced out around the top cap
Overfilled: grease forced out around the top of the ball joint cap.

Overfilling can also force grease out around the top of the ball joint cap, like in the photo above. A little there is normal venting (see tip 5). Globs like this mean you kept pumping too long.

A torn boot is the real problem. It lets grease out and lets dirt and water in, and that's what wears ball joints out early. If you've torn one, a JBA Max 90 ball joint boot set is an easy fix.

5. Grease coming out doesn't mean something failed

Grease coming out of your ball joint boots isn't a leak. It's venting, and that's exactly how JBA ball joints are designed to work.

Factory ball joints are disposable, so they have to be 100% sealed: they get greased once in their whole service life. JBA ball joints are built to last a decade or more, so like the joints on bulldozers, farm tractors and army tanks, they're greaseable. Each time you pump in fresh grease, it fills every passage and cavity in the ball joint housing and pushes the old, used-up grease out into the dust boot. The boot is clamped at the top to hold it in place, but it's otherwise unsealed so the old grease can vent out and make room for the new.

  • Bushings: Grease pushing out of the EZ Lube ports is exactly what you want. It's how you know the bushing is full.
  • Ball joint: Old grease venting out of the boot or around the top of the joint is normal. Wipe it off and you're done.

When should you worry? If the boot is torn or split, if grease is leaking between services and not just while you're greasing, or if you feel clunking or play in the front end. Then check the signs your ball joint UCAs need to be replaced.

Think your JBA ball joint is worn out? Check it the right way

Every ball joint is a wear part, but JBA Max 90 ball joints should last most people 8 to 10 years or more, even with regular off-road use. About 85% of the time someone thinks a JBA ball joint has worn out early, it hasn't.

The usual ball joint check is made for disposable, crimped ball joints like the factory ones. On those, vertical play means the joint is worn. JBA Max 90 ball joints use a wear-compensating upper race kept under load by an internal spring, a feature you'll also find on many heavy-duty 3/4-ton and 1-ton OEM ball joints. Push up and down on one and you're just compressing that spring, so it can feel worn when it's working exactly as designed.

Here's how to check a JBA ball joint:

  1. Put a jack under the lower control arm, as close to the lower ball joint as you can, and lift the tire off the ground.
  2. Put your hands at 12 and 6 o'clock on the tire.
  3. Push and pull the top and bottom of the tire in and out.
  4. If there's movement, look closely at the upper ball joint for side-to-side (radial) play.

If it feels loose, give it a thorough greasing with a primed, good-quality gun first (see tip 2). And if you're not sure your ball joints have ever been greased, do it now. We see never-greased ball joints more often than you'd think, even on trucks from professional shops. It's like running an engine with no oil.

How to grease JBA upper control arms, step by step

You don't need to pull anything apart. The arms stay on the truck, and the whole job takes a few minutes per side. 

  1. Get set up. Load a quality grease gun with Mobilgrease XHP 222 Special.
  2. Wipe the fittings. Clean each grease fitting with a rag before you connect, so you don't push dirt into the joint.
  3. Grease the ball joint. Give it 3 to 4 pumps, until the dust boot just starts to swell. Stop there. You're filling the joint, not inflating the boot.
  4. Grease the bushings. Pump grease into each bushing fitting until you see it consistently pushing out of the EZ Lube ports. That's how you know the bushing is full.
  5. Wipe off the extra. Clean up any grease that squeezed out so it doesn't collect dirt and grit.
  6. Repeat on the other side.

Every JBA arm built since our first production run in October 2019 uses EZ Lube bushings, and they can take more than one pump at each service.

How often should I grease my upper control arms?

Grease the ball joints and bushings every 3,000 to 5,000 miles. An easy way to remember: do it at every oil change.

Grease them again after any day in mud pits, creeks or water crossings, even if you're not due. Fresh grease pushes out water and grit before they can start wearing the joint.

If you wheel often, run big tires or drive a lot of wet or salted roads, stay toward the 3,000-mile end. Some customers have gone 100,000 miles on a set of JBA ball joints, and regular greasing is a big part of how they got there.

When a ball joint does eventually wear out, you don't need a new arm. See 7 ways JBA replaceable ball joints make your life easier, and check the signs your ball joint UCAs need to be replaced.

The bottom line

The right grease, a primed gun, the right amount and a regular schedule make your JBA upper control arms last as long as they can. Use Mobilgrease XHP 222 Special, give each ball joint 3 to 4 pumps, fill the bushings until grease shows at the EZ Lube ports, and repeat every 3,000 to 5,000 miles.

Grab a grease cartridge or the grease gun and grease bundle, or shop JBA upper control arms by vehicle. Questions? Our team is happy to help.

Frequently asked questions

What grease does JBA recommend for its upper control arms?

Mobilgrease XHP 222 Special, a lithium complex grease with 0.75% molybdenum disulfide. Other lithium moly EP greases with a similar makeup also work.

Can I use Red 'n Tacky on JBA upper control arms?

No. Lucas Red 'n Tacky can make the bushings squeak within a short time and eventually damage them. Avoid other red greases and some synthetics for the same reason.

How many pumps of grease go in a JBA ball joint?

3 to 4 pumps, until the dust boot starts to swell. Don't keep pumping past that point.

How do I know the bushings are full?

Keep pumping until grease consistently pushes out of the EZ Lube ports on the bushing.

How often should I grease JBA upper control arms?

Every 3,000 to 5,000 miles, and again after any day in mud or water.

Do I need to remove the arms to grease them?

No. Every ball joint and bushing has its own grease fitting, so you grease them with the arms on the truck.

Which upper control arms can you grease?

Only arms with greaseable ball joints and bushings. Many factory arms use sealed ball joints that can't take new grease. Every JBA upper control arm has a grease fitting on its Max 90 ball joint and on each EZ Lube bushing.

Do lifted trucks need new upper control arms?

Not every truck. A lift or leveling kit puts factory arms at a steeper angle, which drops caster and pushes the ball joint closer to the edge of its travel. Whether you need new arms depends on your vehicle and lift height. See Do lifted trucks need upper control arms?

What should I look for in upper control arms for a lifted truck?

Look for geometry that corrects caster for your lift height, a ball joint you can grease and replace on its own, greaseable bushings, a durable coating and a strong warranty. JBA upper control arms are made in the USA with a replaceable Max 90 ball joint, EZ Lube bushings, a 10-stage powder coat prep process and a lifetime structural warranty.

Is grease coming out of my ball joint boot a problem?

No. JBA ball joint boots are clamped at the top but otherwise unsealed, so old grease vents out as fresh grease goes in. Worry only if the boot is torn, grease leaks between services, or you feel clunking or play.

Why won't my grease gun push grease into the fitting?

It's usually an air pocket. Loosen the head about a thread or crack the bleeder valve, pump until grease flows steadily, then tighten it back down. Make sure the coupler is seated square on the fitting.

How long do JBA ball joints last?

Most people get 8 to 10 years or more out of JBA Max 90 ball joints, even with regular off-road use, as long as they're greased regularly.

How do I check if my JBA ball joint is worn out?

Jack under the lower control arm near the lower ball joint until the tire is off the ground, then push and pull the tire at 12 and 6 o'clock. If it moves, look for side-to-side (radial) play at the upper ball joint. Don't judge it by up-and-down play: the Max 90's spring-loaded upper race is designed to compress.

Why does my JBA ball joint feel loose?

Often the spring-loaded upper race is stuck from too little grease or a poorly primed grease gun. A thorough greasing with a good gun usually pushes it back into place.